DC12V 24V Automatic for PWM PC CPU Fan Temperature Control Speed Controller 2-way 4A

Features: brand new high quality Made of high-quality materials for durability This governor (type PWMTS06) uses for PWM modulation technology to achieve temperature control, and controls the fan speed according to the ambient temperature of the governor. The higher the temperature, the faster the speed. When the ambient temperature is lower than the set start temperature, the governor controls The fan stops running. Whether it is a 2-wire, 3-wire or 4-wire fan, whether it is a for PWM or a brushless fan, as long as the fan voltage is within 24V and the current is less than 4A, the governor is applicable! It is also possible to drive multiple fans. Wide voltage range, super , support multi-voltage DC fan: 12V 24V. Support 2/3/4-wire DC fan speed, users can realize automatic temperature control without purchasing expensive 4-wire for PWM fan speed. for PWM speed regulation adopts industrial grade chips, frequency conversion technology, stable performance and precise control, eliminating the need for general large heat sink linear speed regulators, lower consumption, higher efficiency, and more economical installation space. for Dynamic LED indicators, intuitively understand the real work of the governor. Most of the devices are packaged by for SMD, with stable performance, small size and space saving. The temperature sensor is connected with the cable in the form of a mounting hole, which is convenient for detecting the temperature and specifying the temperature point. In the constant temperature mode and the temperature is 30 degrees, the governor controls the fan to start, the fan speed increases linearly from 30 to 50 degrees, and the fan runs at full speed above 50 degrees. Adjustable mode start temperature range: 10 to 50 degrees, full speed range 30 to 70 degrees (start and full speed temperature difference 20 degrees). The maximum operating temperature of the temperature is 110 degrees. If the temperature exceeds this temperature, the probe will be damaged. hu0657-2 NO.1(Vin+): DC positive terminal port NO.2(Vin-): negative terminal port of DC supply NO.3(F1+): Positive pole of the first DC fan NO.4(F1-): The first DC fan negative port NO.5(F2+): Positive pole of the second DC fan NO.6(F2-): The second DC fan negative port NO.7: Temperature sensor interface NO.8: LED indicator, the light is on to indicate that the governor is working normally NO.9: LED work light, when the ambient temperature is lower than the startup temperature, the light goes out, indicating that the governor turns off the of the fan this time, when the ambient temperature is higher than the startup temperature, the light starts to flicker and the flickering frequency becomes faster, and the fan turns Faster (also means that the currently detected temperature continues to rise), from flashing to steady light, indicating that the fan is entering full-speed at this time, and it is also a high temperature ! NO.10: Mode switch, switch to F gear, the drive is in constant temperature mode, switch A gear, the governor is in temperature adjustment mode NO.11: Temperature adjustment potentiometer, the temperature range of the governor can be set by rotating the potentiometer Product size: 55*35*20mm (installation for M3) Sensor cable length: 30cm Application: This section provides industrial-grade technology solutions for fully regulated industrial environments. 1. Outdoor enclosure, save the noise of the cabinet fan 2. Save room fan noise 3. Other thermostat fan speed applications instruct: 1. Follow the interface instructions to connect the and fan cables. 2. Insert the temperature into the governor and secure the metal part of the probe in the heated area. 3. Turn on the , the governor adjusts the fan speed according to the temperature detected by the temperature . 4. About the use of fixed mode and adjustable mode: 1): In fixed mode, turn the No. 10 switch to F, the temperature range of the governor is fixed at 30 degrees to start the fan at low speed, and 50 degrees to start the fan at full speed. At this time, it is useless to adjust the No. 11 potentiometer. 2): Adjustable mode, start No. 10 to A position, at this time, the temperature range of the governor is set by the No. 11 potentiometer. No. 11 potentiometer has been adjusted to the lowest starting temperature position (10 degrees, corresponding to 30 degrees at full speed) when leaving the factory. When the potentiometer No. 11 is turned clockwise slowly, the temperature range of the governor will gradually increase. After turn, the temperature of the governor will become the highest range (50 to 70 degrees). Package Included: 1 * 4A for PWM PC CPU Fan Temperature Control Speed Controller 1 * 30CM temperature probe Note: 1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness. 2.Please allow slight manual measurement deviation for the data.