KEBIDU wireless remote control 433MHz DC 12V 10A 1CH RF relay, transmitter receiver module with RF relay remote control multifunctional garage door opener

1. Please note that the remote control for learning cannot copy the code of other remote control and can only be used with the controller module.

2. copy type can only copy the code of the original remote control, the original remote control must be complete.

Please pay attention to the selection.

Description:

Material: Plastic

Color: As Picture Show

Type: wireless remote

For: such as telescoping remote control door, electric remote control, road door and so on, remote control alarm.

Nominal Voltage: 12V battery (included)

Wireless transmission distance: 50-150 (M) (open area)

Features

Versatile and versatile, simple design, personalized and easy to use and quick to use

This intelligent remote copy control is suitable for electric remote control doors, remote control doors, sliding doors, remote garage doors, remote control doors.

Chip type mud:

2260 (pt2260, sc2260, lx2260, hx2260); 2262,(pt2262, sc2262, lx2262, hs2262, hx2262), pt2264, pt2240 (lx2240),1527 hx1527), fp527, cs5211, smc918, smc926, ax5026, AX5326-3,AX5326-4, ht600, ht680, ht6207, ht6010, ht6012, ht6013, ht6014 the chip manufacturer has different chip models, prefix, as long as the digital part of the chip can be the same model.

Note: normally we do not recommend copying the rolling code chip as there are so many uncertainty when copying the rolling code chip when copying the remote control rolling code chip. or not, so we do not recommend copying the remote control rolling code.

Take steps:

1. Clear Code: two fingers at the same time, hold the lock key and lock key; LED light flashes fast 3 times in about 2 seconds; let one of the fingers go (the other hand cannot be left), then use the loose finger to click three times quickly on the loose button until the LED light flashes fast; two fingers can be released; then press any button of the remote control; when the LED light goes off, it means that the code is clear, successful (four keys are completely empty); after you press any button of the remote control, the light will still turn on, indicating that the original code is not already cleared, you have to clear it again and clear the code successfully, so you can successfully clone it. can wash and clone repeatedly code.

2. Reproduction: Left hand using the original remote control, right hand uses our cloning remote control and keep two remote controls as close as possible. press the first button of two remote controls at the same time; in about 2 seconds, the LED light will flash quickly 2 times; after one second, the indicator light flashes and let it go to your finger; then press the button after successful, the light will turn on, which means that the first code on the original remote control has been copied to other remote controls. Third... If the copy is finished, the remote control function is the same as the original matching remote control.

3. Restore: when you accidentally clear a copy of the remote control code, you can press a copy of the remote control of the two buttons at the same time, the LED light will flash quickly. For remote control, before using the Remote Copy control, please make sure to remove the existing code from the remote control.

4. how to cope with the situation where some keys can control the remaining incontrollable? You can use clear actions and recover specific operations as follows:

(1) first clear code;

(2) after clearing the code, copy the unsuccessful key again and no need to copy the remaining button.

(3) then clear the code again;

(4) recall the code at the moment, the unsuccessful copy key is covered with a new code and the copied original key will be now stored. again until all keys are successfully copied.

Caution:

1. choose the remote control of prerequisites: The original remote control function is normal, the remote control chip is the same or compatible, the remote control operation frequency is the same.

2. remote control can only copy the code to learn about one chip code and remote control (can copy the chip model, see copy chip type)

3. two-way remote control, rolled code remote control, single chip encoder program can not be copied, such as hcs200, hcs201, hcs300, HCS301 and so on.

4. before copying the remote control, make sure to clear the available code on the remote control and check if the code is cleared successfully. Otherwise, it cannot be copied.

5. please make sure your remote control has enough power. The distance between the two remote controls is even better! Press and hold the button on the original remote control to complete the normal signal, then press the button on the remote control to ensure the function is completely copied.

Note:

1. please accept 1-3mm difference. Due to manual measurement

2. due to different display and light, the picture may not show the actual color of the item. thank you for your understanding.

Inside package include:

1*433MHz remote control

• Input voltage: 12 V

• RF operation mode: Superheterodyne

• Receiver sensitivity: > 97 dBm

• Transmission distance:> 100 meters (open area)

• Decoding mode: Decode MCU software

• Remote storage: 20

• Supports remote type: learning code ev1527

• Operating mode: momentary, toggle lock delay (5 seconds, 10 seconds, 15 seconds)

• Output terminal: No, NC, com

• PCB size: 35x30x18mm (L, w, h)

• Remote control battery: 3x2 v CR2016 button batteries

Note: The maximum input power is 250 V

Remote programming

-Code washing:

Press the learning button on the receiver 8 times, the code will be reset.

After washing the remote code must be re-adjusted.

-Momentary mode

Please contact us for detailed use instructions.

-Learning code:

(Switch-press remote button to open, press again to close)

Press the learning key on the receiver 2 times. wait a moment, the LED will turn off. it will enter the learning status.

-Press the learning button on the receiver 3 times. LED (on the receiver) will flash 3 times.

When the LED light is on, press the remote control button (you let it want to learn) and press the remote a button, the LED flash light 3 times.

Push button remote b LED flash light 3 times

After 3 seconds, the LED light kit goes off, learn to succeed.

Package included

1 * receiver module

1 * remote control (with battery)