Lensent JDIAG T200 auto Full OBD2 OBDII Code Reader obd2 scanner Car Diagnostic tool PK ELM327



📌Warm Tip: JDIAG T200 only supports Engine system and cannot support ABS SRS Airbag system. If you need equipment that supports these systems, please contact the seller to provide new products

📌and JDIAG T200 equipment is directly connected to the car's OBD2 diagnostic socket to obtain power for diagnosis, just plug in Ready to use, no need to recharge

📣 Product Introduction

The T200 scanner is suitable for all OBD ll compliant vehicles(matching up to 97% of the car models), and supports fault codelookup,reading vehicle information, viewing real-time datastreams, fault code reading,fault code clearing,l/M readiness testing, etc., making the T200 the best choice for automotive repair tools.



📣 Supported Protocols

1. ISO9141-2 (5 baud init, 10.4 Kbaud)

2. SAE J1850 PWM (41.6 Kbaud)

3. SAE J1850 VPw (10.4 Kbaud)

4. ISO14230-4 KWP (5 baud init, 10.4 Kbaud)

5. ISO14230-4 KWP (fast init, 10.4 Kbaud)

6. ISO15765-4 CAN (11bit ID, 500 Kbaud)

7. ISO15765-4 CAN (29bit ID, 500 Kbaud)

8. ISO15765-4 CAN (11bit ID, 250 Kbaud)

9.ISO15765-4 CAN (29bit ID,250 Kbaud)



📣 Product Specification:

📌Display Screen: 2.4-inch TFT color screen (320*240)

📌Operating Temperature: -20~60℃ (-4~140°F)

📌Storage Temperature: -20~70℃ (-4~158°F)

📌External Power: 8V-30V DC



📣This is specifically designed for the engine called the "car heart". It is necessary to keep an eye on the engine status to ensure the efficient operation of the engine to ensure your travel safety. In addition, it can also be used before you send the car to the emission test. Great for daily repair work. The table below describes the purpose of each mode of operation:

1. Read Code

2. Erase Code

3.Live Data

4. Freeze Frame

5. I/M readiness

6. O2 Sensor Test

7. On-Board Monitor Test

8. EVAP System

9. Vehicle Information

10. Component Test

DTC Lookup

📣 Operating Instructions



📌Connecting The Scanner

1.Turn off the ignition switch

2.Locate the vehicle's 16-pin data link connector

3.Plug the OBDll cable into the vehicle's DLC

4.Turn on the ignition and engine

5.When finished, the device automatically enters the diagnostic interface



📌Read DTC

Select [OBD] and then [Read DTC], press the [OK] key to continue, if there is a fault code, the screen will display the code (Fig. 2), if you find more than one DTC fault code, please use the left/right keys to turn the page to check all the codes.



📌Clear DTC

Before clearing the fault code, please follow the prompts of the fault code to carry out vehicle maintenance, vehicle maintenance can be completed to clear the faultcode operation.

Select [Clear DTC] and press the [OK] key to continue, the display will show as follows:

NOTE:Clearing a fault code does not mean that the fault code in the ECU has been completely eliminated; the fault code will continue to appear as long as the vehicle has a fault.



📌I/M Status

The [I/M Status] function is used to check the operation of the emissions system on OBD Ⅱ compliant vehicles, and is an excellent feature for checking vehicle compliance with nation-al emissions testing. It is an excellent feature for checking vehicle compliance with theNational Emissions Test. The l/M status can be selected from Clear Fault Ready or CurrentCycle Ready.The l/M shortcut can also be used for one-touch access.

Select [I/M Status] and press the [OK] key to continue, the display will be as follows:



📌ECU lnfo

The ECU Vehicle Information function retrieves information about the vehicle's framenumber, calibration number, and calibration verification number.

Select [ECU Info] and press the [OK] key to continue.The display is as follows:

📌Live Data

View Real-Time Data allows viewing of real-time vehicle PID data, all supported data is displayed and can be viewed by quickly flipping the page with the left/right buttons or selecting custom data for comparison.



📌O2 Sensor

Oxygen sensors are tested to identify problems related to fuel efficiency and vehicleemissions.The Oxygen Sensor test does not support the CAN communication protocol, which is available in Mode 6 for vehicles with CAN communication protocol.



📢 Note:

1.Please allow 1-3cm error due to manual measurement. pls make sure you do not mind before you bid.

2.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!